Thursday, June 10, 2010

Building a curved trestle

In the track plan for the small layout, there is a curved bridge. After much research, I decided to use the common pile trestle kit from Blair-Line. This kit can be built straight or curved, and the price was reasonable. 

The kit is very neatly packed, and the pieces are quite precise. I started with painting all the pieces with a dark brown acrylic prior to assembly as recommended.

The kit comes with various templates for building the bridge. Straight and about 8 various radii templates are available. I found that taping the template to the workbench and using double sided tape to attach the pieces to the template as you are gluing them together works very well. Below are a few pictures of the intermediate piles being built using the template.

DSC04249 

DSC04250 DSC04251

These intermediate piles are quite finicky. The pieces are round, so they don’t want to stay where you want them.  I used a scrapbooking adhesive tape to keep them in place while the glue dried.  Something like this. After the glue dried, I slid a thin sheet of paper underneath the piles to remove them from the template paper.

Next was the end piles and end bents.  The bents came pre-assembled, so all I had to do was to attach the piles to the bents.  These were a lot easier than the intermediate piles.

DSC04265Next, I had to glue the stringers together. To keep them together, I used standard clips you can find at any office store.  You probably have some laying around in the house as was the case with me.

DSC04285The next step was to cut the stringers based on the curved bridge template.  Uh-oh!  I didn’t have a tool that could cut that without destroying it.  So, I picked up a miter-cut precision tool made by Fourmost Products. This worked like a charm. You can probably get by with a razor blade, which is essentially what this tool is.  But, I plan to build several wood kits, including some from scratch, so I thought I can get the use out of this tool down the stretch.

Anyways, the following few pictures show the stringers being cut and put together.

DSC04357 DSC04358 DSC04359 The bridge comes with a micro-engineering bridge flex-track. I carefully bent this according to the template. I use code-80 Peco track on my layout. So, I got a piece and connected it to the bent bridge track and ran a hopper through several times.  The car rolled quite freely.

DSC04360Satisfied with the connection, I proceeded to glue the guard rails to the outside edges of the bridge track.

DSC04361Then I glued the stringer pieces to the bottom of the track.  This part went quite fast also. It was relatively easy when you have a nice precise cut on the stringers. The template was a great help too.

DSC04362  
DSC04363

Then I started gluing the intermediate piles in place. These I had to hold in place with a pair of tweezers for about 30 seconds to get the glue to set.

DSC04364

Last step: the end bents!

DSC04365

Voila!  All done.  Turned out pretty nice.

DSC04366

DSC04368

DSC04370

DSC04374   

After taking some pictures, I turned it upside down and let the glue dry completely overnight. Well, it probably didn’t need to dry overnight, but I was pushing midnight on a weekday, so it dried overnight.

In the morning, I carefully measured how deep I needed to carve the opening on the layout. As I said above, I use code-80 Peco track. The track is on Woodland Scenics foam roadbed. As it turns out, I had to carve the underlying extruded foam exactly 2cm deep to have the rails line up correctly.  This will obviously change based on what type of track you use.  I essentially put the bridge upside down, took a piece of code-80 flex track and attached it to the bridge and laid down a piece of roadbed. Then I measured the distance from the bottom of the roadbed to the bottom of the end bent.

Here are a few pictures of the bridge in place on the layout.

DSC04375

DSC04376

DSC04378

DSC04379   

I can’t wait to get the rest of the track laid and watch the trains roll over the trestle!

 

3 comments:

  1. Thanks for taking the time to write this excellent tutorial. I may have to find an excuse to use this on my layout! Very thorough and good pictures, too.

    ReplyDelete
  2. nice article, love the look of the trestle.

    ReplyDelete
  3. Thanks for the article. Much appreciated.

    ReplyDelete